How to measure.

A Knappa cover slips over the frame you already have. To make it sit snug, we need three numbers in millimetres. It takes two minutes, and you don't unscrew anything.

WWidthleft to right edge of the frame
HHeighttop to bottom edge of the frame
DSticks outfrom the wall to the highest point of the key
πŸ“ruler or calliper (mm)πŸ’³something flat and stiff: a bank card or a book✍️somewhere to write 3 numbers

1Width and height

Lay the ruler flat on the frame. Measure the plastic frame around the key, from the outer left edge to the outer right edge. Then do the same from top to bottom.

  • Measure the frame, not the key and not the box in the wall.
  • Most EU frames are square, so W and H are usually the same. Measure both anyway.
  • Write exactly what you see, to 0.5 mm. Don't add any margin. We add the fit gap ourselves.
key W = 86 H = 86 zero of the ruler on the outer edge of the frame
Front view. The numbers are an example; write your own.

2Rounded or bevelled edges

Many frames are soft, rounded or have a slanted edge. A ruler lying on top then shows a smaller number than the real size.

Measure across the widest points, where the frame meets the wall. Hold the ruler right against the wall, or hold two flat things (two cards) against the sides and measure between them.

We need the maximum size. If the cover is made to the smaller one, it won't go on.
wall key frame, seen from above βœ“ 86, widest point βœ— 80, flat top view from above, looking down the wall
Ruler across the flat top = too small. Measure at the wall.

3How far it sticks out

  1. Put the ruler next to the switch, zero against the wall, pointing straight out at you.
  2. Lay the card flat on the highest point of the key, parallel to the wall, so it reaches the ruler.
  3. Read where the card crosses the ruler. That's D.
  • A rocker key tilts. Measure the side that sticks out more.
  • Measure to the key, not just the frame. The cover has to clear the key.
  • Sockets: measure to the highest point, usually the rim around the holes.
wall frame key, tilted card on the highest point D = 15 read here β†’ 15 mm
Side view. Typical D for EU switches is 7–16 mm.

4Frame for 2 or 3

On a multi-frame (two switches side by side, switch + socket…) you can't measure one section on its own. So:

  1. Measure the short side. Across a horizontal row that's the height, H.
  2. Measure the full length of the frame.
  3. Take away 71 mm for every extra section. That's W for one section.
sectionsone section =
2full length βˆ’ 71
3full length βˆ’ 142

4 in a row: not yet. A cover that long is too big for us to make, for now.

Example: 3 in a row, full length 228 mm β†’ 228 βˆ’ 142 = 86. Or let the calculator below do the maths.
Vertical column? Same, but it's the full height you shorten.

Why 71: across Europe, the boxes in the wall sit 71 mm apart, centre to centre.

full length 228 H 86 7171 228 βˆ’ 71 βˆ’ 71 = W 86
Centre to centre is always 71 mm. You don't need to measure it.

Know your brand? Shortcut.

Pick the series in the configurator and W and H fill in for you. Then you only measure D. The brand is usually printed on the frame's bottom edge or on the key.

Gira E2, Standard 55 Β· 80.7Jung A, LS Β· 81Schneider Asfora, Sedna Β· 83ABB Zenit Β· 85Legrand Valena Β· 86

Not in the list (Liregus, Vilma and other local brands)? Measure with a ruler; it's the same two minutes. Even with a preset, a quick check with a ruler doesn't hurt: series of one brand differ.

Six mistakes we see most

βœ— 8.6βœ“ 86. Everything is in millimetres, not centimetres.
βœ— Measured the keyβœ“ Measure the frame around it. The key is always smaller.
βœ— Ruler on a rounded topβœ“ Measure the widest points, at the wall (step 2).
βœ— Whole multi-frame as oneβœ“ Take 71 mm off for every extra section (step 4).
βœ— D to the frame onlyβœ“ D goes to the highest point of the key, on its high side.
βœ— Added β€œa bit extraβ€βœ“ Write the exact size. The fit gap is built in.

The configurator checks your numbers and warns you if something looks off: a frame under 78 or over 92 mm, or D outside 7–16 mm.

What fits

βœ“ Yes

1-key switch
2 or 3 keys
Socket (EU, round)
Blank plate

βœ— Not yet

Rotary dimmer
Socket with a lid
USB, TV, data
Touch, smart panels

Not sure about yours? Send us a photo of it from the front and from the side before you order. We'll tell you honestly whether it fits.

Got your numbers? Let's build it.

Type what you measured. We do the maths and open the configurator with your size filled in.

Sections

Safety: a cover goes on top of the existing frame. Don't remove the frame or touch anything behind it. That's a job for an electrician.